 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| NEC's 1/2W LOW VOLTAGE UPG2214TK L, S-BAND SPDT SWITCH FEATURES * SWITCH CONTROL VOLTAGE: Vcont (H) = 1.8 to 5.3 V (3.0 V TYP.) Vcont (L) = -0.2 to +0.2 V (0 V TYP.) * LOW INSERTION LOSS: 0.25 dB TYP. @ 0.05 to 0.5 GHz 0.25 dB TYP. @ 0.5 to 1.0 GHz 0.30 dB TYP. @ 1.0 to 2.0 GHz 0.35 dB TYP. @ 2.0 to 2.5 GHz 0.35 dB TYP. @ 2.5 to 3.0 GHz * HIGH ISOLATION: 32 dB TYP. @ 0.05 to 0.5 GHz 28 dB TYP. @ 0.5 to 1.0 GHz 27 dB TYP. @ 1.0 to 2.0 GHz 26 dB TYP. @ 2.0 to 2.5 GHz 24 dB TYP. @ 2.5 to 3.0 GHz * POWER HANDLING: Pin (1 dB) = +27.0 dBm TYP. @ 0.5 to 3.0 GHz, Vcont (H) = 3.0 V/0 V Pin (1 dB) = +20.0 dBm TYP. @ 0.5 to 3.0 GHz, Vcont (H) = 1.8 V/0 V * HIGH-DENSITY SURFACE MOUNTING: 6-pin lead-less package (1.5 x 1.1 x 0.55 mm) * Pb FREE DESCRIPTION NEC's UPG2214TK is a GaAs MMIC L, S-band SPDT (Single Pole Double Throw) switch for mobile phones and other L, S-band applications from 0.5 to 3.0 GHz. This device can operate from 1.8 to 5.3 V with low insertion loss and high isolation. Performance is specified at both 1.8 V and 3.0 V. The UPG2214TK is housed in a 6-pin Pb Free low profile package suitable for high-density surface mounting. APPLICATIONS * L, S-band digital cellular and cordless telephones * BluetoothTM , W-LAN, and WLL * Short Range Wireless ORDERING INFORMATION Part Number UPG2214TK-E2-A Package 6-pin super minimold Marking G4K Supplying Form * Embossed tape 8 mm wide * Pin 1, 6 face the perforation side of the tape * Qty 5 kpcs/reel Remark To order evaluation samples, contact your nearby sales office. Part number for sample order: UPG2214TK-A Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge. California Eastern Laboratories UPG2214TK PIN CONNECTIONS (Top View) 1 2 3 6 5 4 1 2 3 (Top View) 6 5 4 6 5 4 (Bottom View) 1 2 3 PIN NO. 1 2 3 4 5 6 PIN NAME OUTPUT1 GND OUTPUT2 Vcont2 INPUT Vcont1 TRUTH TABLE Vcont1 Low High Vcont2 High Low INPUT-OUTPUT1 ON OFF INPUT-OUTPUT2 OFF ON ABSOLUTE MAXIMUM RATINGS (TA = 25C, unless otherwise specified) PARAMETER Switch Control Voltage Input Power Operating Ambient Temperature Storage Temperature SYMBOL Vcont Pin TA Tstg RATINGS +6.0 Note +30 -45 to +85 -55 to +150 UNIT V dBm C C Note |Vcont1-Vcont2| 6.0 V RECOMMENDED OPERATING RANGE (TA = 25C, unless otherwise specified) Parameter Switch Control Voltage (H) Switch Control Voltage (L) Symbol Vcont(H) Vcont(L) MIN. 1.8 -0.2 TYP. 3.0 0 MAX. 5.3 0.2 Unit V V G4K UPG2214TK ELECTRICAL CHARACTERISTICS PARAMETER Insertion Loss 1 Insertion Loss 2 Insertion Loss 3 Insertion Loss 4 Insertion Loss 5 Isolation 1 Isolation 2 Isolation 3 Isolation 4 Isolation 5 Input Return Loss 1 Input Return Loss 2 Output Return Loss 1 Output Return Loss 2 0.1 dB Loss Compression Input Power Note 2 1 dB Loss Compression Input Power Note 3 2nd Harmonics 3rd Harmonics Intermodulation Intercept Point Switch Control Current Switch Control Speed SYMBOL Lins1 Lins2 Lins3 Lins4 Lins5 ISL1 ISL2 ISL3 ISL4 ISL5 RLin1 RLin2 RLout1 RLout2 Pin (0.1 dB) Pin (1 dB) 2f0 3f0 IIP3 Icont tSW 50% CTL to 90/10% RF (TA = +25C, Vcont (H) = 3.0, Vcont (L) = 0 V, DC blocking capacitors value = 100 pF, unless otherwise specified) TEST CONDITIONS f = 0.05 to 0.5 GHz Note 1 f = 0.5 to 1.0 GHz f = 1.0 to 2.0 GHz f = 2.0 to 2.5 GHz f = 2.5 to 3.0 GHz f = 0.05 to 0.5 GHz Note 1 f = 0.5 to 1.0 GHz f = 1.0 to 2.0 GHz f = 2.0 to 2.5 GHz f = 2.5 to 3.0 GHz f = 0.05 to 0.5 GHz Note 1 f = 0.5 to 3.0 GHz f = 0.05 to 0.5 GHz Note 1 f = 0.5 to 3.0 GHz f = 2.0/2.5 GHz f = 0.5 to 3.0 GHz f = 0.5 to 3.0 GHz f = 2.0 GHz, Pin = +15 dBm f = 2.5 GHz, Pin = +15 dBm f = 2.0 GHz, Pin = +15 dBm f = 2.5 GHz, Pin = +15 dBm f = 0.5 to 3.0 GHz, 2 tone, Pin = +16 dBm, 5 MHz spicing MIN. - - - - - 29 25 24 23 21 15 15 15 15 +21.0 - - - - - - - - - TYP. 0.25 0.25 0.30 0.35 0.35 32 28 27 26 24 20 20 20 20 +23.0 +23.0 +27.0 -55 -55 -55 -55 +58 4 20 MAX. 0.45 0.45 0.50 0.55 0.60 - - - - - - - - - - - - -47 -47 -47 -47 - 20 200 UNIT dB dB dB dB dB dB dB dB dB dB dB dB dB dB dBm dBm dBm dBc dBc dBc dBc dBm A ns Notes 1. DC blocking capacitors = 1,000 pF at f = 0.05 to 0.5 GHz 2. Pin (0.1 dB) is the measured input power level when the insertion loss increases 0.1 dB more than that of linear range. 3. Pin (1 dB) is the measured input power level when the insertion loss increases 1 dB more than that of linear range. UPG2214TK ELECTRICAL CHARACTERISTICS PARAMETER Insertion Loss 6 Insertion Loss 7 Insertion Loss 8 Insertion Loss 9 Insertion Loss 10 Isolation 6 Isolation 7 Isolation 8 Isolation 9 Input Return Loss 3 Output Return Loss 3 0.1 dB Loss Compression Input Power Note 2 1 dB Loss Compression Input Power Note 3 Switch Control Current Switch Control Speed SYMBOL Lins6 Lins7 Lins8 Lins9 Lins10 ISL6 ISL7 ISL8 ISL9 RLin3 RLout3 Pin (0.1 dB) Pin (1 dB) Icont tSW 50% CTL to 90/10% RF (TA = +25C, Vcont (H) = 1.8, Vcont (L) = 0 V, DC blocking capacitors value = 100 pF, unless otherwise specified) TEST CONDITIONS f = 0.05 to 0.5 GHz f = 0.5 to 1.0 GHz f = 1.0 to 2.0 GHz f = 2.0 to 2.5 GHz f = 2.5 to 3.0 GHz f = 0.05 to 0.5 GHz f = 0.5 to 2.0 GHz f = 2.0 to 2.5 GHz f = 2.5 to 3.0 GHz f = 0.05 to 3.0 GHz Note 1 f = 0.05 to 3.0 GHz Note 1 f = 2.0/2.5 GHz f = 0.5 to 3.0 GHz f = 0.5 to 3.0 GHz Note 1 Note 1 MIN. - - - - - 27 23 21 20 15 15 +14.0 - - - - TYP. 0.25 0.25 0.30 0.35 0.35 30 27 25 24 20 20 +17.0 +17.0 +20.0 4 20 MAX. 0.50 0.50 0.55 0.60 0.65 - - - - - - - - - 20 200 UNIT dB dB dB dB dB dB dB dB dB dB dB dBm dBm A ns Notes 1. DC blocking capacitors = 1,000 pF at f = 0.05 to 0.5 GHz 2. Pin (0.1 dB) is the measured input power level when the insertion loss increases 0.1 dB more than that of linear range. 3. Pin (1 dB) is the measured input power level when the insertion loss increases 1 dB more than that of linear range. Caution It is necessary to use DC blocking capacitors with this device. The value of DC blocking capacitors should be chosen to accommodate the frequency of operation, bandwidth, switching speed and the condition with the actual board of your system. The range of recommended DC blocking capacitor value is less than 100 pF for frequencies above 0.5 GHz, and 1,000 pF for frequencies below 0.5 GHz. UPG2214TK EVALUATION CIRCUIT Vcont1 INPUT Vcont2 C0 Note 1,000 pF 6 5 4 1,000 pF 1 C0 2 3 C0 OUTPUT1 OUTPUT2 Note C0 : 0.05 to 0.5 GHz 1,000 pF : 0.5 to 3.0 GHz 100 pF The application circuits and their parameters are for reference only and are not intended for actual design-ins. UPG2214TK ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD Vcont2 6pin L2MM SPDT SW Vc1 OUTPUT2 OUT 1 C 2 C2 C 4 C1 INPUT IN C3 C1 C 5 G4K C C1 1 C2 OUT 2 OUTPUT1 Vc2 Vcont1 USING THE NEC EVALUATION BOARD SYMBOL C1, C2, C3 C4, C5 VALUES 100 pF 1,000 pF UPG2214TK PACKAGE DIMENSIONS 6-PIN LEAD-LESS MINIMOLD (1511) (UNIT: mm) (Top View) (Bottom View) 0.480.05 0.480.05 1.50.1 1.10.1 1.30.05 0.20.1 0.160.05 0.90.1 Remark ( ) : Reference value 0.550.03 0.11+0.1 -0.05 UPG2214TK TYPCIAL CHARACTERISTICS (TA = +25C, Vcount(H) = 3.0 V, Vcont(L) = 0 V, DC blocking capacitors = 100 pF, unless otherwise specified) INPUT-OUTPUT1 INSERTION LOSS vs. FREQUENCY 5 4 Insertion Loss Lins (dB) 3 2 1 0 -1 -2 -3 -4 -5 0.5 1.0 1.5 2.0 2.5 3.0 3.5 1 2 3 4 1: -0.565 dB 1.0 GHz 2: -0.695 dB 1.5 GHz 3: -0.858 dB 2.0 GHz 4: -0.984 dB 2.5 GHz 5: -1.180 dB 3.0 GHz INPUT-OUTPUT2 INSERTION LOSS vs. FREQUENCY 5 4 Insertion Loss Lins (dB) 3 2 1 0 -1 -2 -3 -4 -5 0.5 1.0 1.5 2.0 2.5 3.0 3.5 1 2 3 4 1: -0.571 dB 1.0 GHz 2: -0.695 dB 1.5 GHz 3: -0.848 dB 2.0 GHz 4: -0.981 dB 2.5 GHz 5: -1.151 dB 3.0 GHz 5 5 Frequency f (GHz) Frequency f (GHz) Remark The graphs indicate nominal characteristics. Caution These characteristics values include the losses of the NEC evaluation board. UPG2214TK INPUT-OUTPUT1 ISOLATION vs. FREQUENCY 50 40 30 Isolation ISL (dB) 20 10 0 -10 -20 -30 -40 -50 0.5 1.0 1 2 1.5 3 2.0 4 2.5 5 3.0 3.5 1: -29.06 dB 1.0 GHz 2: -27.83 dB 1.5 GHz 3: -27.417 dB 2.0 GHz 4: -27.232 dB 2.5 GHz 5: -27.188 dB 3.0 GHz INPUT-OUTPUT2 ISOLATION vs. FREQUENCY 50 40 30 Isolation ISL (dB) 20 10 0 -10 -20 -30 -40 -50 0.5 1.0 1 2 1.5 3 2.0 4 2.5 5 3.0 3.5 1: -29.042 dB 1.0 GHz 2: -27.82 dB 1.5 GHz 3: -27.49 dB 2.0 GHz 4: -27.314 dB 2.5 GHz 5: -27.263 dB 3.0 GHz Frequency f (GHz) Frequency f (GHz) INPUT-OUTPUT1 INPUT RETURN LOSS vs. FREQUENCY 50 40 Input Return Loss RLin (dB) 30 20 10 0 -10 -20 -30 -40 -50 0.5 1.0 1 2 1.5 3 2.0 4 2.5 5 3.0 3.5 1: -27.651 dB 1.0 GHz 2: -29.789 dB 1.5 GHz 3: -26.145 dB 2.0 GHz 4: -25.035 dB 2.5 GHz 5: -29.816 dB 3.0 GHz INPUT-OUTPUT2 INPUT RETURN LOSS vs. FREQUENCY 50 40 Input Return Loss RLin (dB) 30 20 10 0 -10 -20 -30 -40 -50 0.5 1.0 2 1.5 1 3 2.0 4 5 3.0 3.5 1: -27.881 dB 1.0 GHz 2: -34.329 dB 1.5 GHz 3: -26.93 dB 2.0 GHz 4: -24.21 dB 2.5 GHz 5: -27.508 dB 3.0 GHz 2.5 Frequency f (GHz) Frequency f (GHz) INPUT-OUTPUT1 OUTPUT RETURN LOSS vs. FREQUENCY 50 Output Return Loss RLout (dB) 40 30 20 10 0 -10 -20 -30 -40 -50 0.5 1.0 2 1.5 1 3 2.0 4 5 3.0 3.5 Output Return Loss RLout (dB) 1: -28.217 dB 1.0 GHz 2: -31.956 dB 1.5 GHz 3: -26.809 dB 2.0 GHz 4: -24.553 dB 2.5 GHz 5: -27.835 dB 3.0 GHz INPUT-OUTPUT2 OUTPUT RETURN LOSS vs. FREQUENCY 50 40 30 20 10 0 -10 -20 -30 -40 -50 0.5 1.0 1 2 1.5 3 4 5 3.0 3.5 1: -26.027 dB 1.0 GHz 2: -28.172 dB 1.5 GHz 3: -24.749 dB 2.0 GHz 4: -23.224 dB 2.5 GHz 5: -26.391 dB 3.0 GHz 2.5 2.0 2.5 Frequency f (GHz) Frequency f (GHz) Remark The graphs indicate nominal characteristics. UPG2214TK OUTPUT POWER vs. INPUT POWER 30 Output Power Pout (dBm) 25 20 15 10 5 10 12 f = 2 GHz 14 16 18 20 22 24 26 28 30 Input Power Pin (dBm) Remark The graphs indicate nominal characteristics. UPG2214TK RECOMMENDED SOLDERING CONDITIONS This product should be soldered and mounted under the following recommended conditions. For soldering methods and conditions other than those recommended below, contact your nearby sales office. Soldering Method Infrared Reflow Soldering Conditions Peak temperature (package surface temperature) Time at peak temperature Time at temperature of 220C or higher Preheating time at 120 to 180C Maximum number of reflow processes Maximum chlorine content of rosin flux (% mass) Peak temperature (package surface temperature) Time at temperature of 200C or higher Preheating time at 120 to 150C Maximum number of reflow processes Maximum chlorine content of rosin flux (% mass) Peak temperature (molten solder temperature) Time at peak temperature Preheating temperature (package surface temperature) Maximum number of flow processes Maximum chlorine content of rosin flux (% mass) Peak temperature (pin temperature) Soldering time (per side of device) Maximum chlorine content of rosin flux (% mass) : 260C or below : 10 seconds or less : 60 seconds or less : 12030 seconds : 3 times : 0.2%(Wt.) or below : 215C or below : 25 to 40 seconds : 30 to 60 seconds : 3 times : 0.2%(Wt.) or below : 260C or below : 10 seconds or less : 120C or below : 1 time : 0.2%(Wt.) or below : 350C or below : 3 seconds or less : 0.2%(Wt.) or below Condition Symbol IR260 VPS VP215 Wave Soldering WS260 Partial Heating HS350 Caution Do not use different soldering methods together (except for partial heating). Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. 02/07/2005 A Business Partner of NEC Compound Semiconductor Devices, Ltd. |
Price & Availability of UPG2214TK
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |